4.9 · 91 Google reviews Licensed & Insured Illinois Roofing Contractor УкраїнськоюУКР (866) 992-2982 Login CRM Login Website Login
State Restoration Services seal STATE RESTORATION SERVICES Roofing · Gutters · Insurance Claims

Gutter apron and drip edge installation for water that runs behind your gutters

When rain comes down between the gutter and the wall while the gutter itself is clear, the fault is usually the strip of metal at the roof edge, or the lack of one. State Restoration Services fits a gutter apron or a drip edge under the first row of shingles so the runoff lands in the gutter, on roofs that stay on and on roofs we are replacing, across the north and northwest Chicago suburbs.

Licensed Illinois roofing contractor 104.018671. The roof edge and the gutter are handled by one crew.

  • No metal at the edge

    Water bends around the shingle, soaks the top of the fascia and runs down behind the gutter.

  • A short edge, cut short

    The metal is there, but it stops above the gap and the shingle stops short of the gutter, so the drip still finds the wall side.

  • Gutter apron lapped into the gutter

    The metal runs from under the shingles over the back of the gutter, so every drop that leaves the roof falls inside it.

Is water getting behind your gutter? What to look for from the lawn

A clogged gutter spills over the front. Water that misses the gutter at the roof edge shows up on the house side, and you can see most of it without a ladder. Our guide on what gutter flashing is explains the part itself; this is the check.

During a steady rain

  • Drips falling between the gutter and the wall while the front lip of the gutter stays dry.
  • Water running down the face of the fascia board under the gutter.
  • Drips from the soffit, or a wet stripe on the siding right below the eave.
  • Puddles at the foundation along a wall where the downspout is working.

On a dry day

  • Dark streaks or peeling paint on the fascia behind the gutter line.
  • No thin strip of metal visible under the bottom row of shingles, only bare wood or the gutter.
  • A shingle edge that stops short of the inside edge of the gutter.
  • Soft or rotted fascia, or mildew along the eaves.
  • A gutter pulling away from the house, which often follows a wet board.

Drip edge or gutter apron: which piece your roof edge needs

Both are bent metal that sits under the first row of shingles. The difference is the lower leg, and that leg decides whether the water reaches the gutter.

2 in or more on the deckdrop

Drip edge

A flange on the deck and a short leg that drops over the fascia, at the eaves and up the rakes.

Where
Eaves and rakes of a shingle roof
Job
Holds the edge of the deck and moves water off the wood
Gap
Can leave a space above the gutter back
flange under the shingleslong leginto the gutter

Gutter apron

The same flange with a longer, angled leg made to lap into the gutter, so the runoff lands in the channel.

Where
Eaves that carry a gutter
Job
Closes the space between roof edge and gutter back
Fit
Added under an existing roof, or set on a new one

The 2012 model building code asks the drip edge to run at least 2 inches up the deck and at least a quarter inch below the sheathing, with pieces lapped 2 inches and fastened 12 inches apart or closer. The shingles then overhang the metal by a quarter to three quarters of an inch on IKO and three eighths to three quarters on GAF, as our page on shingle overhang past the drip edge sets out with the printed sources.

Fitting an apron on a roof that stays on

Most houses do not need a new roof to fix this. The apron goes in along the eaves where water gets behind the gutter, and the shingles above it stay where they are.

If the gutter is sagging or the joints leak as well, that work is done on the same visit and priced the way our gutter repair page shows.

White gutter and downspout at the corner of a roof eave, seen from below against a blue sky
A finished eave corner from our gallery: the gutter sits tight under the roof edge.
  1. Photos of every eaveWet streaks, the fascia and the gap at the gutter back are photographed first, so you see what we saw.
  2. The fascia checked by handA soft or rotted board is priced as its own line and repaired before any metal goes on, never hidden inside the edge price.
  3. The first row of shingles taken off along that edgeOnly the bottom course of the eave being fixed, not the slope above it.
  4. The apron slid under and fastenedIt goes under the shingles and over the back of the gutter, and is fastened to the deck.
  5. The edge closed upGaps are sealed and the shingle row goes back on with its edge reaching past the metal.
  6. The gutter set to the apronWhere a run hangs too low or has pulled away, it is re-hung on hidden hangers at 18 inches.

What it costs: one 40 ft eave, priced three ways

Our published rate for gutter apron installation is $1.00 to $3.00 per linear foot, depending on the metal, how easy the edge is to reach and whether old flashing has to come off. The bars use that rate together with the gutter prices on our repair page.

  • Apron only, 40 ft eave40 ft at $1 to $3

    $40 to $120
  • Apron on every eave, 150 fta whole house, 150 ft at $1 to $3

    $150 to $450
  • Apron plus a new 40 ft gutter runapron $40 to $120, old run off $40 to $80, new run $240 to $560

    $320 to $760
$0$200$400$600$800

Downspouts and fascia work are priced on their own lines. If the runs need more outlets, our downspout installation page shows how those are sized and priced.

On a new roof, the edge is built once and in order

When the roof is being replaced anyway, the edge metal is part of the job and nothing has to be lifted later. On every eave we build it in this order.

  1. Edge metal on the deck

    Drip edge or gutter apron fastened along the eaves, lapped where pieces meet.

  2. Membrane over it at the eaves

    Underlayment and ice-and-water membrane lap over the metal at the eaves and go under it at the rakes.

  3. Starter row

    The hidden first row sets the shingle line, a quarter to three quarters of an inch past the metal.

  4. Gutters last

    The gutters go up under the finished edge, so the apron lands inside them.

When wind or hail bent the roof edge

A storm can lift and bend edge metal and dent the gutter below it, and then water starts getting behind a gutter that worked for years. We photograph and measure the damage and write an estimate for the carrier that follows the code, together with any shingles the wind lifted, which our wind damage roof repair page covers.

A roofer in Illinois may not negotiate an insurance claim. You can be represented on the claim by our partner, the licensed Illinois public adjuster State Adjusting Services, and the insurer decides what it pays. Our office answers Monday to Friday 7 AM to 7 PM and weekends 9 AM to 5 PM.

Questions about gutter aprons and drip edge

What is the difference between a drip edge and a gutter apron?

Both are metal strips under the first row of shingles. A drip edge has a short leg that drops over the fascia, while a gutter apron has a longer angled leg made to lap into the gutter, so the water lands in the channel instead of behind it.

Can a gutter apron be added without replacing the roof?

Yes. The first row of shingles is taken off along the eave being fixed, the apron is slid under the shingles and over the back of the gutter and fastened, and the edge is sealed and closed up again. The rest of the roof stays as it is.

How much does gutter apron installation cost?

Our rate is $1.00 to $3.00 per linear foot, so a 40 ft eave runs about $40 to $120 and a whole house with 150 ft of eaves about $150 to $450. Fascia repair and new gutters, when needed, are priced as separate lines.

Why does water run behind my gutter when it is not clogged?

Usually the roof edge has no metal, or a short drip edge stops above the gap and the shingles end short of the gutter. The water then follows the metal and the fascia down the house side of the gutter, which is what an apron stops.

Want this looked at?

We inspect for free, document what we find and prepare a code-compliant estimate you can hand to your insurer. Our partner, a licensed public adjuster, State Adjusting Services, can represent you on the claim.

Call (866) 992-2982. Free Inspection